Click Here

 

What are your concepts about How to Install a Bathtub Yourself?

Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough task. If the old tub is conveniently easily accessible, the task can move easily; if you have to open a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly need a helper to move out the old tub and embeded in the new one. Make certain you have actually qualified yourself for the job as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This write-up will help you mount a brand-new bathtub in your restroom if you have currently purchased a brand-new bathtub and do not need to transform the plan of your previous water system pipes.
Your devices and product checklist should consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic as a result of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines remain in place between the faucet and also the sink. Safeguard the tap in place with the maker supplied backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type ought to be linked to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Tub

Making use of the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto four little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub until the spirit level reviews degree.
To install taps, fit the bottom of the furthest versatile tap port to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and also inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the tub and likewise examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of once as this will certainly settle it right into its final position.

 

 

Getting ready for the Installment

Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.

 

 

Tiling Around the Bath tub

In the location where the bathroom meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealant can break relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about How to Install a Bathtub Yourself? Place feedback further down. We will be glad to hear your reactions about this piece. In hopes that you visit us again later on. Sharing is caring. Helping others is fun. Thanks for your time. Visit us again soon.

Explore Now